全文获取类型
收费全文 | 232篇 |
免费 | 66篇 |
国内免费 | 54篇 |
专业分类
航空 | 221篇 |
航天技术 | 40篇 |
综合类 | 21篇 |
航天 | 70篇 |
出版年
2024年 | 1篇 |
2023年 | 7篇 |
2022年 | 3篇 |
2021年 | 8篇 |
2020年 | 8篇 |
2019年 | 8篇 |
2018年 | 9篇 |
2017年 | 20篇 |
2016年 | 16篇 |
2015年 | 7篇 |
2014年 | 14篇 |
2013年 | 16篇 |
2012年 | 15篇 |
2011年 | 17篇 |
2010年 | 7篇 |
2009年 | 18篇 |
2008年 | 13篇 |
2007年 | 19篇 |
2006年 | 23篇 |
2005年 | 19篇 |
2004年 | 14篇 |
2003年 | 14篇 |
2002年 | 10篇 |
2001年 | 7篇 |
2000年 | 8篇 |
1999年 | 13篇 |
1998年 | 6篇 |
1997年 | 5篇 |
1996年 | 6篇 |
1995年 | 1篇 |
1994年 | 8篇 |
1993年 | 2篇 |
1992年 | 3篇 |
1991年 | 1篇 |
1990年 | 4篇 |
1989年 | 2篇 |
排序方式: 共有352条查询结果,搜索用时 15 毫秒
21.
以不同界面层厚度的SiC纤维为增强相,采用先驱体浸渍裂解工艺(PIP)制备SiCf(PyC)/SiC复合材料,并在复合材料基体中引入SiC晶须,对其性能进行研究。结果表明:热解碳(PyC)界面层厚度约为230 nm时,SiC纤维拔出明显,SiCf/SiC复合材料拉伸强度、弯曲强度和断裂韧度分别达到192.3 MPa、446.9 MPa和11.4 MPa?m1/2;在SiCf/SiC复合材料基体中引入SiC晶须后,晶须的拔出、桥连及裂纹偏转等增韧机制增加了裂纹在基体中传递时的能量消耗,使复合材料的断裂韧度和弯曲强度分别提高了22.9%和9.1%。 相似文献
22.
研究 NR1155天然橡胶在不同硫化压力下热硫化后的物理力学性能。基于90°粘合剥离强度测试方法分别测量了不同硫化压力下制备的橡胶/金属复合结构试样的粘合剥离强度,并采用低场 NMR 橡胶交联密度测定仪分析试样中橡胶部分的交联密度,同时采用冷场发射电子扫描显微镜(SEM)研究剥离破坏表面。结果表明:NR1155天然橡胶胶料与 Chemlok205/Chemlok220热硫化胶粘体系具有很好的相容性和协同硫化作用。随着硫化压力的提高,橡胶/金属的粘合剥离强度呈现先降低后增加的规律,且最大剥离力呈现对硫化压力的函数依赖关系,而硫化胶的交联密度则呈现相反的趋势。 相似文献
23.
24.
Analyses toward factors influencing sealing clearance of a metal rubber seal and derivation of a calculation formula 总被引:1,自引:1,他引:0
《中国航空学报》2016,(1):292-296
Sealing clearance is a key factor for a metal rubber seal’s sealability. The expansion coef-ficient and expansion deformation in the radial direction of metal rubber have been obtained through a thermal expansion experiment of metal rubber. The influence of the elastic modulus to the sealing clearance has been analyzed theoretically. By combining the temperature and elasticity factors of metal rubber with the elastic mechanics theory, the calculation formula of the sealing clearance has been derived, and the values of the sealing clearance and the leakage rate in certain working conditions have been calculated. Experimental results are consistent with calculation results in a high degree. The calculation formula of the sealing clearance can explain the influences of the temperature and elastic modulus factors of metal rubber on the sealing clearance. It can pro-vide guidance for the study of sealing mechanism of metal rubber seals. 相似文献
25.
为研究硅橡胶基防热涂层高温下的力学性能,针对两种硅橡胶基防热涂层开展高温压缩试验,对其截面的宏观及微观形貌进行分析,并结合高温下的热失重分析,探讨了其高温压缩强度变化规律及机理。研究结果表明:甲基苯基硅橡胶涂层高温热解温度区间主要为500~650℃,最终质量残余率为67.61%,其高温压缩强度在25~800℃呈增加趋势,由于玻璃小球的软化及树脂基体的热解,导致在400及700℃两个温度点的压缩强度降低,但在800℃由于玻璃小球与涂层中填料、烧蚀产物等发生共融,使涂层力学性能显著增加。甲基乙烯基硅橡胶涂层的高温热解温度区间主要为450~800℃,最终质量残余率为89.95%,由于甲基乙烯基硅橡胶涂层在高温热解后产生的陶瓷相,弥补了树脂裂解所带来的强度下降,因此在25~800℃其高温压缩强度较为稳定,并未产生明显衰减。影响硅橡胶基防热涂层高温力学性能的因素主要包括树脂基体的热解以及填料在高温下发生的物理-化学变化。 相似文献
26.
27.
28.
采用熔体混熔方法结合挤压铸造制备了Al—8wt.%Si合金。利用SEM、DSC、TEM和力学性能测试等分析手段研究了合金的组织及性能。结果显示,通过将高温的A1-30%Si合金熔体和低温的工业纯铝金属液混和,凝固形成的亚共晶成份Al.08wt.%Si合金中含有3%左右的细小初生si相。与传统熔体变质处理后制备Al.8wt.%Si合金的相比,经初生Si相增强的Al—Si合金拉伸强度达到185MPa,抗弯强度达到437MPa,分别提高15%和19%,同时延伸率增加近1倍达到6.7%。 相似文献
29.
长期受粒子辐照、紫外辐照等因素的影响,地球同步卫星的太阳电池阵输出功率会出现较为明显的衰减。这里选取某地球同步卫星使用的背表面反射(BSR)硅太阳电池阵为研究对象,采用光强因子和温度因子修正太阳电池阵的输出功率,使用局部加权回归散点平滑法(LOWESS)分析了其在设计寿命期间的输出功率衰减规律;同时基于LOWESS建立了预测模型,用于硅太阳电池阵超寿运行期间的功率预测。实测数据表明:本文构建的预测模型可以满足超寿地球同步卫星在轨管理使用需求。 相似文献
30.
It is urgent to carry out detailed research on storage performance of rubber sealing ring to get the criterion for its storage life. This paper acquires material ageing regularity by theoretical analysis and experimental confirmation. On this condition, failure mode and failure criterion of typical sealing structure is studied, and the failure mechanism is found. Thus by analyzing the stress distribution, the relationship between ageing state and sealing condition is established. Rationalization proposal is put forward and storage life of sealing ring is evaluated. The research mentionedabove has special reference to the design of sealing structures and can provide reference for prolonging their service life. 相似文献